Відео

I have questions how can I personally write you you gave me a lot if I fo ive been looking for

Bud where are you located?! I have a 2010 Dodge Charger I'm planning on building when I get a settlement from my motorcycle accident and I want my 3.5 to sound like this!! I'm in Missouri

Would you be able to use this to tune for a cam? I have a 99 ram and it feels like it's impossible to find a tuner for magnums or 2nd gen rams

I don't know The funny thing is is if you go over to a Ford front-end Dana 50 half shaft u- joint replacement, almost every video I pulled up was so concerned about pushing the u-joints out so you didn't bend any part of it. Is the Dana 50 that much weaker than the Dana 60? Also super curious is there not any kind of dust cap going into the axle tube at the end of the half shaft? I feel like there should be something there to keep dirt and rocks and crap from getting into the axle tube....

I’m having this problem with a 2007 charger 2.7 i ordered the part and when i went to fix it the pink thingy wasn’t even broken. What else could be causing it to not go out of park?

Love your video, I have a 97 dodge ram 1500,5.9l I want to do a single turbo whar kind of fuel injection I need

If you rebuild make sure there well be no left over metal fragments stuck in the block

What is that special tool. Been trying to find one.

5.7 HEMI runs on 5W-20 Engine Oil after the Re-Build can it run on 5W-30 or 5W-40 Engine Oils ?

What type cams did you use? Or where did you get them. Plus will they fit in the 3.5 heads instead of the 4.0

Have this issue, don't have a shop or the tools to complete this work. What would someone expect to pay to get the driver side fixed?

Where is the 47re rebuild video?

Nice!

Bump

how much and how much to do mine

can i daily this car?>!

Where are Gator fasteners made? It is not on their website. I assume they are yellow instead of red, white and blue.

Found bc looking into stuff for my truck lolz same motor love the turbos and the pipes way u ran them looks great

1997 don't have a map sensor

👍💪

do you have dimensions for the cluste rpiece you cut out? i want to do something like this.

Do you have a more in depth guide of how to get that whole assembly out? I cant get it out of the cavity its sitting in

What a little pink piece of crap! Thanks, just saved me a tow to my garage for my Magnum R/T…Urg…

Have the Pistons held up?

Terimakasih saran nya broo

Thanks no information on this truck thanks.

Are stock pushrods good to run or do you need a set specific to the new cam? 3:47

I thank you very much for your absolutely wonderful experience and well explained to us ! God bless your bissnes and your family!❤😅🎉

Can I take them off, and not put them back in?

What about a Comp Cam for a 5.7 Hemi 🤔🤔🤔🤔

do you adjust preboost screw all the way out, all the way in, did you tune it? did you adjust afc housing back or forward?

Mine is a 97 Sport and I can't find the one piece that will fit my truck. Anyone have a link? I didn't realize they would be different than a regular 97 Ram.

how much for the turbo kit

Took it all apart in my hot ass garage, and ordered the metal replacement thanks to you, cheers from Canada, very helpful.

You stretched the metal as it was cooling by pushing on it with the rag, splash water on it or lay a soaked rag on top and it should work better, nice build man!

Does the harmonic balancer need to go in a certain way? I have a brand new short block 5.7 hemi and I can’t find if it matters or if you just slap it on? Great video, I used it to make sure I was building it properly. Thanks for being so descriptive.

How much torque did it make?

Send #

Just killed me. Subscribed.

Thanks saved me a lot of time and effort

What will be the length if you 6" lifted?